Enclosed is our latest new products rochure

Read More
Home > IMMO Emulator>BMW EWS2 EWS3.2 EMULATOR

BMW EWS2 EWS3.2 EMULATOR

χ

This item was already in your inquiry basket.

Enter inquiry basket now.

  • Product Details
  • Make an Inquiry

Descriptions for BMW EWS2 EWS3.2 Emulator

Installation:

1. Remove original EWS2 control unit, find +12v ACC, GND, K-line wires, attach emulator. Emulator must be in service mode: JUMPER 1 shorted.

2. Connect ANY K-line diagnostic adapter to vehicle diagnostic connector and launch Emulator Configuration Utility:


3. Choose COM port, write in desired ISN number, press button Store.

4. For some ECUs, it is possible to read ISN number directly from engine control unit. In this case, select option "ECU xxxxx", press Read. Software will try to read ISN. If successful, choose option "EWS emulator" and press button Store to save ISN number into emulator.

5. Disconnect emulator from K-line, remove JUMPER 1 and connect K output from emulator to DME (DDE) EWS line.

6. Don't forget to short two starter relay wires (EWS connector)!

7. Car is ready to start.



What is immo emulator used for?
Immo emulator replace damaged immobilizers or car keys.

In case of EWS3.2 similar procedure is used, only difference is that it is NOT connected directly to diagnostic K-line.

There are NO any counters or car starts limited. You can change and store new ISN without any limitations.

Emulator is shipped with JUMPER 1 shorted. For testing purposes, ISN 0579 is stored by default.



EWS-connection



Descriptions for BMW EWS2 EWS3.2 Emulator

Installation:

1. Remove original EWS2 control unit, find +12v ACC, GND, K-line wires, attach emulator. Emulator must be in service mode: JUMPER 1 shorted.

2. Connect ANY K-line diagnostic adapter to vehicle diagnostic connector and launch Emulator Configuration Utility:






3. Choose COM port, write in desired ISN number, press button Store.


4. For some ECUs, it is possible to read ISN number directly from engine control unit. In this case, select option "ECU xxxxx", press Read. Software will try to read ISN. If successful, choose option "EWS emulator" and press button Store to save ISN number into emulator.


5. Disconnect emulator from K-line, remove JUMPER 1 and connect K output from emulator to DME (DDE) EWS line.


6. Don't forget to short two starter relay wires (EWS connector)!


7. Car is ready to start.






In case of EWS3.2 similar procedure is used, only difference is that it is NOT connected directly to diagnostic K-line.


There are NO any counters or car starts limited. You can change and store new ISN without any limitations.


Emulator is shipped with JUMPER 1 shorted. For testing purposes, ISN 0579 is stored by default

Function:
Immo emulator replace broken immobilizers or car keys.

Warranty:
Easy Plug&Play installation System
Good quality product
1 Years Warranty


What is immo emulator used for?
Immo emulator replace damaged immobilizers or car keys.


Where is the immo emulator located?
It is in the bottom of the passenger seat.


What should i do when the immobilizer is damamged?
This device is self-learning a computer code in case of losing the car keys or a car burglary,it enable to drive off from the road to the car service.
Due to a low cost you can leave it in the car instead of buying a new immo or making car keys duplicate. There is a possibility of using it as the additional security!!!


Contact Information
Email: info@caremulator.com
MSN: info@caremulator.com
Skype: sinosellscom

Agree with this Privacy Policy
Please choose if you agree to the privacy policy